march 2009 rev 1 1/9 9 HDMI05-CL02F3 5-line ipad?, hdmi? cont rol line esd protection features low line capacitance: 12 pf max. high efficiency in esd protection lead-free package very thin package high reliability offered by monolithic integration high reduction of parasitic elements through integration and wafer level packaging complies with the standards: iec 61000-4-2 level 4 ? 15 kv (air discharge) ? 8 kv (contact discharge) iec 61000-4-2 level 1 ? 2 kv (air discharge) ? 2 kv (contact discharge) application where esd protection for hdmi control lines (cec, hpd, scl and sda) is required: mobile phones and communication systems portable multimedia players camcorder, digital still cameras description the HDMI05-CL02F3 chip is a low capacitance esd protection for hdmi control pins. it also integrates pull-up resistor for i2c bus and pull- down resistor for hot plug detect and pull-up resistor for cec line. the esd protection circuitry prevents damage to the protected device when subjected to esd surges up to 15 kv. figure 1. pin configuration (bump side) figure 2. schematic tm : ipad is a trademark of stmicroelectronics. hdmi, the hdmi logo and high-definition multimedia interface are tradmarks or regist ered trademarks of hdmi licensing llc. flip chip 9 bumps b c 1 2 3 a scl cec sda hpd gnd gnd rpu2 rpu 5v scl sda hpd cec 5v b2 and c2 are ground pins c1 a2 a1 a3 b3 c3 r1 r2 r3 r4 b1 www.st.com
characteristics HDMI05-CL02F3 2/9 rev 1 1 characteristics table 1. absolute maximum ratings (t amb = 25 c) symbol parameter value unit v pp external pins (a1, a2, a3, b3 and c3): esd iec 61000-4-2, level 4 - air discharge esd iec 61000-4-2, level 4 - contact discharge internal pins (b1, c1): esd iec 61000-4-2, level 1 - air discharge esd iec 61000-4-2, level 1 - contact discharge 15 8 2 2 kv pd line resistance power dissipation at 70 c 60 mw t op operating temperature range -30 to + 85 c t stg storage temperature range -55 to + 150 c table 2. electrical characteristics (t amb = 25 c) symbol parameter v br breakdown voltage i rm leakage current @ v rm v rm stand-off voltage v cl clamping voltage r d dynamic impedance i pp peak pulse current r i/o series resistance between input and output c line line capacitance symbol test condition min typ max unit v br i r = 1 ma 6 20 v i rm v rm = 3 v per line 50 200 na r 1 , r 2 1575 1750 1925 r 3 80 100 120 k r 4 22 27 32 k c line v line = 0 v, v osc = 30 mv, f = 1 mhz cec to gnd with r pu2 not connected scl and sda to gnd with r pu not connected (measured under zero light conditions) 14 24 17 29 pf c line (1) 1. this is the line capacit ance seen by the data signals in the application conditions v line = 0 v, v osc = 30 mv, f = 1 mhz cec, scl and sda to gnd with r pu and r pu2 grounded (measured under zero light conditions) 10 12 pf i v i f v f i rm i r i pp v rm v br v cl slope = 1/r d
HDMI05-CL02F3 characteristics rev 1 3/9 figure 3. s21(db) versus frequency figure 4. analog crosstalk measurements 300.0k 1.0m 3.0m 10.0m 30.0m 100.0m 300.0m 1.0g 3.0g - 20.00 - 15.00 - 10.00 - 5.00 0.00 300.0k 1.0m 3.0m 10.0m 30.0m 100.0m 300.0m 1.0g 3.0g - 20.00 - 15.00 - 10.00 - 5.00 0.00 300.0k 1.0m 3.0m 10.0m 30.0m 100.0m 300.0m 1.0g 3.0g - 20.00 - 15.00 - 10.00 - 5.00 0.00 db cec sda 5v scl hpd f(hz) 300 . 0 k1. 0 m 3 . 0 m1 0 . 0 m 30 . 0 m1 00 . 0 m 300 . 0 m1. 0g 3 . 0g - 160.00 - 120.00 - 80.00 - 40.00 0.00 db f(hz) cec - rpu2 hpd - scl sda - scl scl - cec scl - rpu figure 5. esd response to iec 61000-4-2 (+8 kv contact discharge) on cec line figure 6. esd response to iec 61000-4-2 (-8 kv contact discharge) on cec line 10 v/div 72 v 52 v 39 v 20 ns/div v : esd peak voltage v @ 30 ns: clamping voltage @ 30 ns v @ 60 ns: clamping voltage @ 60 ns pp cl cl 1 1 2 2 3 3 10 v/div -17 v 2 -11 v 3 -52 v 1 20 ns/div v : esd peak voltage v @ 30 ns: clamping voltage @ 30 ns v @ 60 ns: clamping voltage @ 60 ns pp cl cl 1 2 3 figure 7. esd response to iec 61000-4-2 (+8 kv contact discharge) on scl line figure 8. esd response to iec 61000-4-2 (-8 kv contact discharge) on scl line 20 ns/div 10 v/div 70 v 48 v 39 v 1 2 3 v : esd peak voltage v @ 30 ns: clamping voltage @ 30 ns v @ 60 ns: clamping voltage @ 60 ns pp cl cl 1 2 3 20 ns/div 10 v/div -51 v -17 v -11 v 1 2 3 v : esd peak voltage v @ 30 ns: clamping voltage @ 30 ns v @ 60 ns: clamping voltage @ 60 ns pp cl cl 1 2 3
characteristics HDMI05-CL02F3 4/9 rev 1 figure 9. esd response to iec 61000-4-2 (+8 kv contact discharge) on sda line figure 10. esd response to iec 61000-4-2 (-8 kv contact discharge) on sda line 10 v/div 79 v 51 v 39 v 1 2 3 20 ns/div v : esd peak voltage v @ 30 ns: clamping voltage @ 30 ns v @ 60 ns: clamping voltage @ 60 ns pp cl cl 1 2 3 10 v/div -57 v -22 v -14 v 1 2 3 20 ns/div v : esd peak voltage v @ 30 ns: clamping voltage @ 30 ns v @ 60 ns: clamping voltage @ 60 ns pp cl cl 1 2 3 figure 11. esd response to iec 61000-4-2 (+8 kv contact discharge) on hpd line figure 12. esd response to iec 61000-4-2 (-8 kv contact discharge) on hpd line 10 v/div 65 v 40 v 49 v 1 2 3 20 ns/div v : esd peak voltage v @ 30 ns: clamping voltage @ 30 ns v @ 60 ns: clamping voltage @ 60 ns pp cl cl 1 2 3 10 v/div -43 v -17 v -11 v 1 2 3 20 ns/div v : esd peak voltage v @ 30 ns: clamping voltage @ 30 ns v @ 60 ns: clamping voltage @ 60 ns pp cl cl 1 2 3 figure 13. esd response to iec 61000-4-2 (+8 kv contact discharge) on 5 v line figure 14. esd response to iec 61000-4-2 (-8 kv contact discharge) on 5 v line 10 v/div 72 v 52 v 39 v 1 2 3 20 ns/div v : esd peak voltage v @ 30 ns: clamping voltage @ 30 ns v @ 60 ns: clamping voltage @ 60 ns pp cl cl 1 2 3 10 v/div -52 v -20 v -14 v 1 2 3 20 ns/div v : esd peak voltage v @ 30 ns: clamping voltage @ 30 ns v @ 60 ns: clamping voltage @ 60 ns pp cl cl 1 2 3
HDMI05-CL02F3 typical application schematic rev 1 5/9 2 typical application schematic figure 15. implementation with hdmi (mobile phone) (tv, flat panel, monitor, projector) multimedia controller multimedia controller gnd tx2+ tx1- gnd tx1+ tx0- gnd tx0+ tc- gnd tc+ cec scl sda hpd gnd tx2+ tx1- gnd tx1+ tx0- gnd tx0+ tc- gnd tc+ cec scl sda hpd video audio ctrl / status video audio ctrl / status v dd _5v v dd _5v type c connector pin - out type c connector pin - out hdmiulc6 - 4f3 hdmi05 - cl02f3 host (mobile phone) display (tv, flat panel, monitor, projector) multimedia controller multimedia controller gnd tx2+ tx1- gnd tx1+ tx0- gnd tx0+ tc - gnd tc+ cec scl sda hpd gnd tx2+ tx1- gnd tx1+ tx0- gnd tx0+ tc - gnd tc+ cec scl sda hpd video audio ctrl / status video audio ctrl / status v dd _5v v dd _5v type c connector pin - out type c connector pin - out hdmiulc6 - 4f3 hdmi05 - cl02f3 5v hpd hdmiulc6-4f3 b2 d3 d1 c3 c1 a1 a3 f1 f3 100k 4 tmds channel HDMI05-CL02F3 cec 5v scl 2 x 1k75 sda tmds data2 shield tmds data1 shield tmds data0 shield tmds clk shield tmds data2 + tmds data2 - tmds data1 + tmds data1 - tmds data0 + tmds data0 - tmds clk + tmds clk - ddc / eec ground cec scl sda reserved +5v power hot plug detect j4 1 2 3 4 5 7 8 9 10 11 12 13 14 16 17 18 19 6 15 27k vdd_cec e2 hdmiulc6-4f3 d3 d1 c3 c1 a1 a3 f1 f3 b2 e2 5v hpd hdmiulc6-4f3 b2 d3 d1 c3 c1 a1 a3 f1 f3 100k 4 tmds channel HDMI05-CL02F3 cec 5v scl 2 x 1k75 sda tmds data2 shield tmds data1 shield tmds data0 shield tmds clk shield tmds data2 + tmds data2 - tmds data1 + tmds data1 - tmds data0 + tmds data0 - tmds clk + tmds clk - ddc / eec ground cec scl sda reserved +5v power hot plug detect j4 1 2 3 4 5 7 8 9 10 11 12 13 14 16 17 18 19 6 15 27k vdd_cec e2 hdmiulc6-4f3 d3 d1 c3 c1 a1 a3 f1 f3 d3 d1 c3 c1 a1 a3 f1 f3 b2 e2 b2 e2 hdmi tx2- tx2- gnd gnd
ordering information scheme HDMI05-CL02F3 6/9 rev 1 3 ordering information scheme figure 16. ordering information scheme 4 package information in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack ? specifications, grade definitions and product status are available at: www.st.com . ecopack ? is an st trademark. figure 17. flip chip dimensions hdmi 05 - cl 02 f3 function number of lines application version package hdmi = hdmi protection 05 = 5 lines cl = control lines 02 = with cec pull-up integrated f3 = flip chip 0.4 mm pitch 1.14 mm 30 m 1.14 mm 30 m 255 m 40 400 m 40 400 m 50 605 m 55
HDMI05-CL02F3 package information rev 1 7/9 figure 20. flip chip tape and reel specification figure 18. footprint figure 19. marking 220 m recommended 220 m recommended 260 m maximum solder stencil opening : copper pad diameter: solder mask opening: 300 m minimum x y x w z w e dot, st logo xx = marking yww = datecode (y = year ww = week) z = manufacturing location user direction of unreeling all dimensions in mm 4.0 0.1 8.0 0.3 4.0 0.1 1.75 0.1 3.5 - 0.1 ? 1.5 0.1 0.69 0.05 1.24 1.24 st e xxz yww st e xxz yww st e xxz yww
ordering information HDMI05-CL02F3 8/9 rev 1 5 ordering information table 3. ordering information 6 revision history table 4. document revision history order code marking package weight base qty delivery mode HDMI05-CL02F3 jg flip chip 1.76 mg 5000 tape and reel (7?) date revision changes 24-mar-2009 1 first issue.
HDMI05-CL02F3 rev 1 9/9 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. unless expressly approved in writing by an authorized st representative, st products are not recommended, authorized or warranted for use in milita ry, air craft, space, life saving, or life sustaining applications, nor in products or systems where failure or malfunction may result in personal injury, death, or severe property or environmental damage. st products which are not specified as "automotive grade" may only be used in automotive applications at user?s own risk. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2009 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com
|
